Audi S4

since 2000 release

Repair and operation of the car



Audi S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures when carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   - External equipment
      Installation of the forward panel in situation for maintenance
      Removal and installation of a cover of a water-collecting compartment
      Removal and installation of a front bumper
      Removal and installation of a loker of a back wing
      Removal and installation of a loker of a forward wing
      Removal and installation of a forward wing
      Removal and installation of a rear bumper
      Removal and installation/adjustment of a cowl
      Removal and installation of a cable of the drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and installation of a door
      Adjustment of a door
      Removal and installation of a frame of a window of a forward door
      Removal and installation of a window regulator
      Removal and installation of the electric motor of the drive of a window regulator
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a trunk lid
      Removal, installation and adjustment of a trunk lid
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Station wagon)
      Removal and installation of a door of a back (Station wagon)
      Removal and installation of the lock of a door of a back (Station wagon)
      Removal and installation of an external mirror
      Removal and installation of moldings
      Removal, installation and check of the movable panel of a roof
      Removal and installation of an overlay of the movable panel of a roof
      Check and adjustment of a starting position of the movable panel of a roof
      Removal and installation of a sealant of the movable panel
      Replacement of elastic bands of brushes of a screen wiper
      Removal and installation of a jet of windscreen washer of a windshield
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of screenwash
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets of a faroomyvatel
      Adjustment of levers of a screen wiper
   + Equipment of salon
+ Onboard electric equipment


4affa92a



Removal and installation of a door of a back (Station wagon)

Removal

 PERFORMANCE ORDER

  1. Disconnect a negative cable (-) of the rechargeable battery.

Observe indications of the Section Replacement of the Rechargeable Battery.

  1. Remove facing of a door of a back, address the Section Removal and installation of facing of a door of a back (Station wagon).
  2. Disunite sockets of heating of back glass and screen wiper, and also the uniform lock. Disconnect a hose of a washer of back glass.

It is necessary for simplification of installation will fix a cord which after a pulling of wires remains in a cover on the ends of a wire.

Surely ask the assistant to take a back door before removing a gas-filled emphasis. Otherwise the door can fall since it cannot hold only the account of one damper.

  1. Disconnect above a gas-filled emphasis (1). For this purpose raise the screw-driver a lock spring (3) a little and remove an emphasis from a spherical pin (2). Remove the second emphasis in the same way.
  1. Uncover loops and the guide for a cable located at a loop.
  2. For the subsequent installation: Mark with a felt-tip pen the provision of loops of a door of a back.
  1. Turn out screws (arrows on an accompanying illustration) from a back door at the left and on the right.
  1. Remove a door by means of the assistant.

Installation

 PERFORMANCE ORDER

  1. Establish a door by means of the assistant on loops. Expose an old door at the same time on earlier executed tags.
  2. Screw screws at the left and on the right.
  3. Establish a gas-filled emphasis on a spherical support and insert a lock ring. In the same way establish the second emphasis.
  4. Weaken a lock clamp, close a door and adjust it in relation to adjacent elements.
  5. Tighten screws the moment of 21 Nanometer.
  6. Further installation is carried out in the sequence, the return to removal.
  7. Attach a negative cable (-) of the rechargeable battery.

Observe indications of the Section Replacement of the Rechargeable Battery.

Back door: Check/adjustment

 PERFORMANCE ORDER

  1. Check gaps in interface of a door of a back to adjacent elements of a body. Gaps on all perimeter have to be uniform. The door has to coincide with side elements of a back part of a body. Over a roof the door should not act more than 0.5 mm.
  1. Turn off nuts (1) and (3) so that the clamp of the lock (2) could be displaced.

The pad (an arrow on an accompanying illustration) on a clamp shows back.

  1. Uncover (1) on the left and right emphasis, and install the adjusting screw (2), having turned it counterclockwise, in situation "0".
  1. Close a door and press it on 2 mm into a body. Open a door and tighten nuts the moment of 21 Nanometer. The door has to be closed on the lock easily and not have a side play. Check gaps.
  1. Adjust the provision of the left and right emphasis so that the closed door had no side play. For this purpose put a little plasticine on an emphasis and close a door. It is possible to judge by a print of plasticine whether the door is correctly adjusted
  1. Establish on a cover emphasis.