Audi S4 + Introduction + Governing bodies and methods of safe operation + Current leaving and service + Engine + Cooling systems, heating and air conditioner + Power supply systems, release and decrease in toxicity of the fulfilled gases + Systems of electric equipment of the engine + Manual box of gear shifting + Automatic transmission + Coupling, power shafts and differential + Brake system + Suspension bracket and steering - Body General information and security measures when carrying out body works Cleaning and leaving Repair of insignificant damages of body panels Repair of considerable damages of a body - External equipment Installation of the forward panel in situation for maintenance Removal and installation of a cover of a water-collecting compartment Removal and installation of a front bumper Removal and installation of a loker of a back wing Removal and installation of a loker of a forward wing Removal and installation of a forward wing Removal and installation of a rear bumper Removal and installation/adjustment of a cowl Removal and installation of a cable of the drive of a cowl Removal and installation of a clamp of the lock Removal and installation of facing of a forward door Removal and installation of facing of a back door Removal and installation of a door Adjustment of a door Removal and installation of a frame of a window of a forward door Removal and installation of a window regulator Removal and installation of the electric motor of the drive of a window regulator Removal and installation of the lock of a door Removal and installation of the handle of a door Removal and installation of the cylinder of the lock of a door Removal and installation of facing of a trunk lid Removal, installation and adjustment of a trunk lid Removal and installation of the lock of a luggage carrier Removal and installation of facing of a door of a back (Station wagon) Removal and installation of a door of a back (Station wagon) Removal and installation of the lock of a door of a back (Station wagon) Removal and installation of an external mirror Removal and installation of moldings Removal, installation and check of the movable panel of a roof Removal and installation of an overlay of the movable panel of a roof Check and adjustment of a starting position of the movable panel of a roof Removal and installation of a sealant of the movable panel Replacement of elastic bands of brushes of a screen wiper Removal and installation of a jet of windscreen washer of a windshield Removal and installation of a jet of a washer of back glass Removal and installation of the lever of screenwash Removal and installation of the lever of a cleaner of back glass Removal and installation of jets of a faroomyvatel Adjustment of levers of a screen wiper + Equipment of salon + Onboard electric equipment
|
Removal, installation and adjustment of a trunk lid Sedan
Removal
|
- Disconnect a negative cable (-) of the rechargeable battery.
|
|
- Remove facing of a trunk lid, address the Section Removal and installation of facing of a trunk lid.
- Disunite sockets and take out from a trunk lid.
|
|
For simplification of installation it is necessary to fix a cord which after a pulling of wires remains in a cover on the ends of a wire. |
|
- For repeated installation: Mark with a felt-tip pen position of balance weights of loops (3) on a trunk lid.
|
|
- Remove a gas-filled emphasis, address the Section Removal and installation of a door of a back (Station wagon).
- Ask the assistant to take a trunk lid and turn off 2 nuts of fastening (1) and (2) at the left and on the right in a trunk lid.
- Remove a trunk lid by means of the assistant.
|
|
Installation
|
- Establish a trunk lid by means of the assistant into place. Expose an old cover on earlier put tags.
- Screw two nuts at the left and on the right.
- Establish a gas-filled emphasis, address the Section Removal and installation of a door of a back (Station wagon).
- Release maple the lock, close a trunk lid and adjust its situation so that the gap on a contour of a prileganiye was uniform, address appropriate section.
- Tighten a nut the moment 21 Nanometer.
- Further installation is carried out in the sequence, the return to removal.
- Attach a negative cable (-) of the rechargeable battery.
|
|
Check and adjustment
|
- Check trunk lid gaps. The gap on a contour of a prileganiye has to be uniform.
|
|
- Remove facing of overlapping of a back, address the Section Removal and installation of facings (Sedan).
|
- Weaken nuts (1) so that it was possible to displace maple the lock (2).
|
|
- Close a trunk lid and adjust a gap on a prileganiye contour.
- Open a trunk lid and tighten nuts of fastening of the maple lock the moment of 8 Nanometers.
- Establish into place facing of overlapping of a back, address the Section Removal and installation of facings (Sedan).
|
- Remove rubber covers (2) on an emphasis at the left and on the right and screw an emphasis (1) completely in a trunk lid.
|
|
- Screw an emphasis so that the closed cover (3) was aflush with adjacent elements of a body, and an emphasis slightly adjoined to a cargo edge (4).
- Put on rubber covers an emphasis.
|
|
|
|