Audi S4

since 2000 release

Repair and operation of the car



Audi S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures when carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   - External equipment
      Installation of the forward panel in situation for maintenance
      Removal and installation of a cover of a water-collecting compartment
      Removal and installation of a front bumper
      Removal and installation of a loker of a back wing
      Removal and installation of a loker of a forward wing
      Removal and installation of a forward wing
      Removal and installation of a rear bumper
      Removal and installation/adjustment of a cowl
      Removal and installation of a cable of the drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and installation of a door
      Adjustment of a door
      Removal and installation of a frame of a window of a forward door
      Removal and installation of a window regulator
      Removal and installation of the electric motor of the drive of a window regulator
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a trunk lid
      Removal, installation and adjustment of a trunk lid
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Station wagon)
      Removal and installation of a door of a back (Station wagon)
      Removal and installation of the lock of a door of a back (Station wagon)
      Removal and installation of an external mirror
      Removal and installation of moldings
      Removal, installation and check of the movable panel of a roof
      Removal and installation of an overlay of the movable panel of a roof
      Check and adjustment of a starting position of the movable panel of a roof
      Removal and installation of a sealant of the movable panel
      Replacement of elastic bands of brushes of a screen wiper
      Removal and installation of a jet of windscreen washer of a windshield
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of screenwash
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets of a faroomyvatel
      Adjustment of levers of a screen wiper
   + Equipment of salon
+ Onboard electric equipment


4affa92a



Removal and installation of the handle of a door

Handle of a forward door

1 — a door handle Support
2 — the door Lock
3 — the Driving bar
4 — the Bolt, 20 Nanometers
5 — a lock cylinder Cover
6 — the lock Cylinder

7 — the door Handle
8 — the Driving lever
9 — the Holder of a clip
10 — the Latch
11 — the door Handle

Removal and installation of the handle of a forward and back door essentially do not differ.

Removal

 PERFORMANCE ORDER

  1. Remove a door upholstery, address the Sections Removal and installation of facing of a forward door and Removal and installation of facing of a back door.
  2. Remove a door frame with a window regulator from a door, address the Sections Removal and installation of a frame of a window of a forward door and Removal and installation of a window regulator.
  3. Take out a driving bar (3) from the holder of a clip (9).
  4. Insert the screw-driver черезпанель doors from within, incline in the direction of an arrow and release a latch (10) at the handle of a door (11).
  5. Disconnect the door handle from a support and take out from a door.

Installation

 PERFORMANCE ORDER

  1. Install into place the handle of a door and record it in a support.
  2. Connect a driving bar (3) to a clip (9), incline a clip on 90 ° and record on a driving bar.
  3. Establish a door upholstery, address appropriate section.