Audi S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
General information and security measures when carrying out body works
Cleaning and leaving
Repair of insignificant damages of body panels
Repair of considerable damages of a body
- External equipment
Installation of the forward panel in situation for maintenance
Removal and installation of a cover of a water-collecting compartment
Removal and installation of a front bumper
Removal and installation of a loker of a back wing
Removal and installation of a loker of a forward wing
Removal and installation of a forward wing
Removal and installation of a rear bumper
Removal and installation/adjustment of a cowl
Removal and installation of a cable of the drive of a cowl
Removal and installation of a clamp of the lock
Removal and installation of facing of a forward door
Removal and installation of facing of a back door
Removal and installation of a door
Adjustment of a door
Removal and installation of a frame of a window of a forward door
Removal and installation of a window regulator
Removal and installation of the electric motor of the drive of a window regulator
Removal and installation of the lock of a door
Removal and installation of the handle of a door
Removal and installation of the cylinder of the lock of a door
Removal and installation of facing of a trunk lid
Removal, installation and adjustment of a trunk lid
Removal and installation of the lock of a luggage carrier
Removal and installation of facing of a door of a back (Station wagon)
Removal and installation of a door of a back (Station wagon)
Removal and installation of the lock of a door of a back (Station wagon)
Removal and installation of an external mirror
Removal and installation of moldings
Removal, installation and check of the movable panel of a roof
Removal and installation of an overlay of the movable panel of a roof
Check and adjustment of a starting position of the movable panel of a roof
Removal and installation of a sealant of the movable panel
Replacement of elastic bands of brushes of a screen wiper
Removal and installation of a jet of windscreen washer of a windshield
Removal and installation of a jet of a washer of back glass
Removal and installation of the lever of screenwash
Removal and installation of the lever of a cleaner of back glass
Removal and installation of jets of a faroomyvatel
Adjustment of levers of a screen wiper
+ Equipment of salon
+ Onboard electric equipment
|
Removal and installation of a frame of a window of a forward door
Frame of a window of a forward door
Removal
|
|
- Disconnect a negative cable (-) of the rechargeable battery.
- Remove a door upholstery, address appropriate section.
- Disunite all sockets.
- Remove the window regulator electric motor, address the Section Removal and installation of the electric motor of the drive of a window regulator.
- Turn out consistently bolts (7), (4), (8), (10), (6) and (9), previously having uncovered (5).
- Take out a frame of a window (1) with a window regulator (2) from a door (3) up. An arrow – the fixing screw.
|
|
Installation
|
|
- Enter glass on a half into a window frame.
- Insert a window frame with a window regulator from above into a door.
- Press carving fingers of the electric motor of a window regulator via the internal panel of a door so that they were recorded.
- Lay above a door sealant at a window frame.
- Screw consistently bolts (6), (9), (4), (8), (10) and (7).
- Tighten by hand bolts (6) and (9).
- Press from above a window frame inside and tighten bolts (4) and (8) moment of 32 Nanometers. Press on a cover (5).
- Tighten bolts (6) and (9) moment of 32 Nanometers.
- Tighten a bolt (10) the moment of 10 Nanometers.
- Tighten bolts (7) the moment of 6 Nanometers.
- Tighten the fixing screw (shooter) the moment of 32 Nanometers.
- Install into place the window regulator drive electric motor, address the Section Removal and installation of the electric motor of the drive of a window regulator.
- Join the socket.
- Establish a door upholstery, address the Section Removal and installation of facing of a forward door.
- Attach a negative cable (-) of the rechargeable battery.
|
|
|
|
