Audi S4 + Introduction + Governing bodies and methods of safe operation + Current leaving and service + Engine + Cooling systems, heating and air conditioner + Power supply systems, release and decrease in toxicity of the fulfilled gases + Systems of electric equipment of the engine + Manual box of gear shifting + Automatic transmission + Coupling, power shafts and differential + Brake system + Suspension bracket and steering - Body General information and security measures when carrying out body works Cleaning and leaving Repair of insignificant damages of body panels Repair of considerable damages of a body - External equipment Installation of the forward panel in situation for maintenance Removal and installation of a cover of a water-collecting compartment Removal and installation of a front bumper Removal and installation of a loker of a back wing Removal and installation of a loker of a forward wing Removal and installation of a forward wing Removal and installation of a rear bumper Removal and installation/adjustment of a cowl Removal and installation of a cable of the drive of a cowl Removal and installation of a clamp of the lock Removal and installation of facing of a forward door Removal and installation of facing of a back door Removal and installation of a door Adjustment of a door Removal and installation of a frame of a window of a forward door Removal and installation of a window regulator Removal and installation of the electric motor of the drive of a window regulator Removal and installation of the lock of a door Removal and installation of the handle of a door Removal and installation of the cylinder of the lock of a door Removal and installation of facing of a trunk lid Removal, installation and adjustment of a trunk lid Removal and installation of the lock of a luggage carrier Removal and installation of facing of a door of a back (Station wagon) Removal and installation of a door of a back (Station wagon) Removal and installation of the lock of a door of a back (Station wagon) Removal and installation of an external mirror Removal and installation of moldings Removal, installation and check of the movable panel of a roof Removal and installation of an overlay of the movable panel of a roof Check and adjustment of a starting position of the movable panel of a roof Removal and installation of a sealant of the movable panel Replacement of elastic bands of brushes of a screen wiper Removal and installation of a jet of windscreen washer of a windshield Removal and installation of a jet of a washer of back glass Removal and installation of the lever of screenwash Removal and installation of the lever of a cleaner of back glass Removal and installation of jets of a faroomyvatel Adjustment of levers of a screen wiper + Equipment of salon + Onboard electric equipment
|
Removal and installation of an external mirror Replacement of a mirror
Removal
|
- Disconnect a negative cable (-) of the rechargeable battery.
|
|
- Open a door and take out a triangular slip from three holders of clips. At the same time at first disconnect a slip below.
|
- Turn out the screw (7) and remove a mirror with the block of adjustment (2) from a door (5).
|
|
- Disunite the socket (6). (3) – lower cover.
|
|
Installation
|
- Installation is carried out in the sequence, the return to removal. At the same time you monitor the correct provision of consolidation (8) at the basis of a mirror (9). Tighten the screw (7) the moment of 12 Nanometers.
- Tighten consolidation at a window frame over a triangular slip.
- Attach a negative cable (-) of the rechargeable battery.
|
|
Mirror glass replacement
Removal
|
- Disconnect a negative cable (-) of the rechargeable battery.
|
|
- Paste over the mirror case with a tape above and below to protect it from damage.
|
|
- Carefully hook a plastic wedge mirror glass at first below, and then above.
|
- Take out glass from the case and disunite the socket of heating of a mirror.
|
|
Installation
Lifting operation and installations of the car on supports is connected with danger! Therefore before carrying out operation study Poddomkrachivaniye's Section and towage.
|
- Establish glass of a mirror (4) on a basic plate (2) and join the socket of heating of a mirror.
|
|
- Insert glass into the directing pins and displace a finger (3) in a frictional spring (shooter).
|
- Record glass, at the same time you press only in the center of glass. (1) – mirror case.
|
- Attach a negative cable (-) of the rechargeable battery.
|
|
|
Replacement of the case of a mirror
Removal
|
- Remove mirror glass, address appropriate section.
|
- Turn out screws (4), disconnect the lower cover (3) from holders and remove down.
|
|
- Disconnect the case of an external mirror (1) from holders (arrow) and remove upward.
|
|
Installation
|
- Install the case of an external mirror from above on the block of adjustment (2).
- Fix the case above and below on the block of adjustment (2). At the same time holders of the block of adjustment have to enter lock hooks of the case.
- Insert from below a cover (3), record and fix.
- Establish into place mirror glass.
|
|
|
|