Audi S4

since 2000 release

Repair and operation of the car



Audi S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures when carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   - External equipment
      Installation of the forward panel in situation for maintenance
      Removal and installation of a cover of a water-collecting compartment
      Removal and installation of a front bumper
      Removal and installation of a loker of a back wing
      Removal and installation of a loker of a forward wing
      Removal and installation of a forward wing
      Removal and installation of a rear bumper
      Removal and installation/adjustment of a cowl
      Removal and installation of a cable of the drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and installation of a door
      Adjustment of a door
      Removal and installation of a frame of a window of a forward door
      Removal and installation of a window regulator
      Removal and installation of the electric motor of the drive of a window regulator
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a trunk lid
      Removal, installation and adjustment of a trunk lid
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Station wagon)
      Removal and installation of a door of a back (Station wagon)
      Removal and installation of the lock of a door of a back (Station wagon)
      Removal and installation of an external mirror
      Removal and installation of moldings
      Removal, installation and check of the movable panel of a roof
      Removal and installation of an overlay of the movable panel of a roof
      Check and adjustment of a starting position of the movable panel of a roof
      Removal and installation of a sealant of the movable panel
      Replacement of elastic bands of brushes of a screen wiper
      Removal and installation of a jet of windscreen washer of a windshield
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of screenwash
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets of a faroomyvatel
      Adjustment of levers of a screen wiper
   + Equipment of salon
+ Onboard electric equipment





Adjustment of a door

Check: Forward door

 PERFORMANCE ORDER

  1. Check gaps in interface of a forward door. Gaps have to be uniform on all perimeter of a prileganiye to a body.

    And — 3.5 ± 0.5 mm
    In — 4.5 ± 0.5 mm
    With — 0 ± 1.0 mm

The back door has to be adjusted.

Check: Back door

 PERFORMANCE ORDER

  1. Check gaps in interface of a back door. Gaps have to be uniform on all perimeter of a prileganiye to a body.

    And — 4.5 ± 0.5 mm
    In — 3.5 ± 0.5 mm
    With — 0 ± 1.0 mm

The back door has to be adjusted.

Adjustment

 PERFORMANCE ORDER

  1. Weaken screws of fastening of a clamp of the lock.
  1. Adjustment of a door in the longitudinal direction: Weaken screws of fastening of loops (arrow A) to a rack A (3) (a back door: a rack (In) so that the door (2) with loops (1) could move in grooves.

To some screws of fastening access is available only from within. For this purpose it is necessary to remove at first the lower upholstery on a rack And or Century. On an accompanying illustration the lower loop at the closed door is shown.

  1. Adjustment of a door in the longitudinal direction: Expose a door according to the set gaps and tighten screws of fastening of loops the moment of 32 Nanometers.
  2. Adjustment of a door in the cross direction, 1 reception: Weaken screws of fastening of loops (arrow B) so that it was possible to displace a door (2) with loops in grooves. Expose a door so that its contour was aflush with adjacent elements of a body. It belongs first of all to a forward part of a door. In a back part the door is regulated at the expense of a lock clamp. Tighten screws of fastening of loops the moment of 32 Nanometers.
  1. Adjustment of a door in the cross direction, the 2nd reception: In a back part of a door adjustment is carried out at the expense of a clamp of the lock (1).

Tags (arrows and / c) are applied to side adjustment, a tag (arrow b/d) for adjustment on height.

  1. Weaken screws (2) and displace a lock clamp. Adjust a clamp so that the door stood a little outside.
  2. Carefully close a door so that was aflush with adjacent elements of a body, and the lock clamp correctly came into the lock.
  3. Tighten screws of fastening of a clamp of the lock the moment of 25 Nanometers.