Audi S4

since 2000 release

Repair and operation of the car



Audi S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures when carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   - External equipment
      Installation of the forward panel in situation for maintenance
      Removal and installation of a cover of a water-collecting compartment
      Removal and installation of a front bumper
      Removal and installation of a loker of a back wing
      Removal and installation of a loker of a forward wing
      Removal and installation of a forward wing
      Removal and installation of a rear bumper
      Removal and installation/adjustment of a cowl
      Removal and installation of a cable of the drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and installation of a door
      Adjustment of a door
      Removal and installation of a frame of a window of a forward door
      Removal and installation of a window regulator
      Removal and installation of the electric motor of the drive of a window regulator
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a trunk lid
      Removal, installation and adjustment of a trunk lid
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Station wagon)
      Removal and installation of a door of a back (Station wagon)
      Removal and installation of the lock of a door of a back (Station wagon)
      Removal and installation of an external mirror
      Removal and installation of moldings
      Removal, installation and check of the movable panel of a roof
      Removal and installation of an overlay of the movable panel of a roof
      Check and adjustment of a starting position of the movable panel of a roof
      Removal and installation of a sealant of the movable panel
      Replacement of elastic bands of brushes of a screen wiper
      Removal and installation of a jet of windscreen washer of a windshield
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of screenwash
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets of a faroomyvatel
      Adjustment of levers of a screen wiper
   + Equipment of salon
+ Onboard electric equipment


4affa92a



Removal and installation of facing of a door of a back (Station wagon)

Lower facing

Removal

 PERFORMANCE ORDER

  1. Open a door of a back and remove the lighting lamp (1), address the Section Removal and installation of plafonds of internal lighting.
  1. Open a cover in facing (3), release the holder and take out the warning sign.
  1. Turn out 4 screws (2).
  1. Remove by means of an exhaust hook 3370 or HAZET 2520-1 top facing from the holder of a clip on the right and at the left).
  1. Take out carefully 6 spring clips (4) from a door of a back and remove facing (3).

Installation

 PERFORMANCE ORDER

  1. Installation is carried out in the sequence, the return to removal. At the same time you watch that facing was correctly included into a cover at the back door lock.

Facing of a back window

Removal

 PERFORMANCE ORDER

  1. Open a door of a back and remove the lower facing of a door of a back.
  1. Turn out 2 screws (1).
  1. Disconnect 2 spring clips (3) from sides from a back door. (4) – rubber emphasis.
  1. Take out 4 spring clips (3) above from a door and remove facing (2).

Installation

 PERFORMANCE ORDER

  1. You monitor the correct provision of eight rubber emphasis.
  2. Establish facing at first on each side, and then above.
  3. Record facing at first above in back door openings, then on each side.
  4. Fix facing by two screws.