Audi S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
General information and security measures when carrying out body works
Cleaning and leaving
Repair of insignificant damages of body panels
Repair of considerable damages of a body
+ External equipment
- Equipment of salon
Remarks on work with the equipment of salon and a security measure
Removal and installation of spring clips
Removal and installation of the central console
Removal and installation of the holder of drinks
Removal and installation of facing of the lever of the parking brake
Removal and installation of a cover of the lever of switching of transfers/selector
Removal and installation of an ashtray
Removal and installation of the central armrest
Removal and installation of an internal mirror
Removal and installation of a cover on the control panel
Removal and installation of a pocket from the driver
Removal and installation of a ware box
Removal and installation of an antisolar peak
Removal and installation of facing are permanent And
Removal and installation of the top facing of a rack In
Removal and installation of the lower facing of a rack In
Removal and installation of a forward overlay of a threshold
Removal and installation of facings (Sedan)
Removal and installation of facings (Station wagon)
Removal and installation of a front seat
Removal and installation of a back seat
Removal and installation of a forward seat belt
Removal and installation of a back seat belt
+ Onboard electric equipment
|
Removal and installation of facings (Station wagon) Rack With
Removal
Installation
|
|
- Installation is carried out in the sequence, the return to removal. At the same time fix a head safety cushion by new screws.
- Put a door sealant over facing.
|
|
During connection of the rechargeable battery in salon there should not be people. |
- Shoot the insulating film from the negative plug of the rechargeable battery, attach at first positive (+), and then a negative cable (-) to the rechargeable battery.
|
|
Facing over a back door
Removal
|
|
|
|
- To exclude operation a head safety cushion, switch off ignition and disconnect at first negative, and then positive cables of the rechargeable battery. Instructions are provided in the Section Replacement of the Rechargeable Battery.
- Disconnect facing behind a rack And.
- Remove facing of a rack of D.
|
- Press down the handle (5) and cast away a cover of the screw (4) down. For this purpose enter a thin wire into a groove (7) and open a cover.
|
|
- Turn out screws (3).
- Turn out the screw (1).
- Turn out the screw (7) for what displace a level in an eye for a dividing grid back.
- Disconnect facing (2) at a spring clip (6) and remove.
|
|
Installation
|
|
- Installation is carried out in the sequence, the return to removal, at the same time tighten the screw (7) the moment of 9 Nanometers.
|
|
During connection of the rechargeable battery in salon there should not be people. |
- Shoot the insulating film from the negative plug of the rechargeable battery, attach at first positive (+), and then a negative cable (-) to the rechargeable battery.
|
|
Rack of D
Removal
|
|
|
|
- To exclude operation a head safety cushion, switch off ignition and disconnect at first negative, and then positive cables of the rechargeable battery. Instructions are provided in the Section Replacement of the Rechargeable Battery.
- Remove the closing roof level, address the Section Removal and installation of facings (Sedan).
- Disconnect a back edge of side facing of a cargo compartment, address appropriate section.
|
- Turn out the screw (3) for what displace a level in an eye for a dividing grid back.
|
|
- Disconnect facing (1) at two spring clips (2) and take out from side facing of a cargo compartment up.
- Take out facing of a rack of D (1) from facing (4) over a door back.
- Weaken screws of fastening of a safety cushion of the head in a back part.
- Turn out screws (6) and remove facing (5) over a back window.
|
|
Installation
|
|
- Installation is carried out in the sequence. the return to removal. At the same time fix a head safety cushion by new screws.
- Put a back cover sealant over facing.
|
|
During connection of the rechargeable battery in salon there should not be people. |
- Shoot the insulating film from the negative plug of the rechargeable battery, attach at first positive (+), and then a negative cable (-) to the rechargeable battery.
|
|
The closing roof level
Removal
|
|
- Disconnect the closing level of a roof (1) at four spring clips (2) and remove.
|
|
|
Installation
|
|
- Installation is carried out in the sequence, the return to removal.
- Put a back cover sealant over closing roof level.
|
|
Side facing of a cargo compartment
Removal
|
|
- Side facing right: Disconnect a negative cable (-) of the rechargeable battery.
|
|
|
- Remove a side pillow of a back seat, address the Section Removal and installation of a back seat.
- Release half of the cargo room and take out.
- Remove an overlay of a cargo compartment, see below.
|
- Turn out screws (4) fastenings of an eye for baggage (5).
|
|
- Turn out the screw (3) and disconnect side facing (2) at spring clips (1).
- Right side facing: Disunite the socket socket.
- Take out side facing.
|
|
Installation
|
|
- Installation is carried out in the sequence, the return to removal.
- Right side facing: Attach a negative cable (-) of the rechargeable battery.
|
|
Overlay of the lock of a cargo compartment
Removal
|
|
- Open a back door.
|
- Turn out 4 screws (1) and carefully disconnect an overlay of the lock (2) from a compartment edge at lock fingers (the shooter on an accompanying illustration). At the same time displace a plastic wedge under a slip and remove each finger separately.
|
|
|
Installation
|
|
- Installation is carried out in the sequence, the return to removal.
|
|
|
|
