Audi S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
General information and security measures when carrying out body works
Cleaning and leaving
Repair of insignificant damages of body panels
Repair of considerable damages of a body
+ External equipment
- Equipment of salon
Remarks on work with the equipment of salon and a security measure
Removal and installation of spring clips
Removal and installation of the central console
Removal and installation of the holder of drinks
Removal and installation of facing of the lever of the parking brake
Removal and installation of a cover of the lever of switching of transfers/selector
Removal and installation of an ashtray
Removal and installation of the central armrest
Removal and installation of an internal mirror
Removal and installation of a cover on the control panel
Removal and installation of a pocket from the driver
Removal and installation of a ware box
Removal and installation of an antisolar peak
Removal and installation of facing are permanent And
Removal and installation of the top facing of a rack In
Removal and installation of the lower facing of a rack In
Removal and installation of a forward overlay of a threshold
Removal and installation of facings (Sedan)
Removal and installation of facings (Station wagon)
Removal and installation of a front seat
Removal and installation of a back seat
Removal and installation of a forward seat belt
Removal and installation of a back seat belt
+ Onboard electric equipment
|
Removal and installation of a back seat Back seat
Removal
|
|
- Strong breakthrough disconnect a seat (arrow A) from holders (1), raise it and pull back (an arrow B on an accompanying illustration).
|
|
- Take out the plug of a side safety cushion from a groove at a back wall of a pillow of a back seat remove a seat.
|
|
Installation
|
|
- Establish a seat into place and insert the plug of a side safety cushion into a groove in a pillow of a back seat.
- Shift a seat back, in front press in holders (1) and record.
|
|
At the same time do not damage holders. |
|
|
Back of a back seat, folding
Removal
|
|
- Cast away a back of a back seat forward.
|
- Hook and uncover behind (3) (an arrow on an accompanying illustration). Turn out the screw (1) and remove a safety collar (2).
|
|
- Lift a back (5) from a support (4) and remove from a side element of fastening (6). If necessary, again put on the plug (7).
|
- Uncover (2) at an armrest (1) in the direction of an arrow.
|
|
- Turn out the screw (3).
- Take out a finger (4) from a loop (5) and take out an armrest.
|
|
Installation
|
|
- Installation is carried out in the sequence, the return to removal.
|
|
Back of a back seat, motionless
Removal
|
|
|
|
- Remove a back seat.
- Take out head restraints from backs.
- Take out guides for head restraints from backs. At the same time insert the small screw-driver obliquely through an opening at a guide, press the screw-driver inside, release a stopper and take out a guide from a back.
- If necessary, take out from a back a bag frame for skis.
-
Models with a side safety cushion: To exclude operation a head safety cushion, switch off ignition and disconnect at first negative, and then positive cables of the rechargeable battery. Instructions are provided in the Section Replacement of the Rechargeable Battery.
-
Models with a side safety cushion: Disunite the safety cushion socket.
|
- Take out a back (1) upward from collars (2) fastenings (3).
|
|
|
Installation
|
|
- Installation is carried out in the sequence, the return to removal.
|
|
During connection of the rechargeable battery in salon there should not be people. |
- Shoot the insulating film from the negative plug of the rechargeable battery, attach at first positive (+), and then a negative cable (-) to the rechargeable battery.
|
|
Side pillow of a back seat
Removal
|
|
|
|
- To exclude operation a head safety cushion, switch off ignition and disconnect at first negative, and then positive cables of a battery room
- Remove a back seat.
|
- Turn out the screw (6).
|
|
- Models with a side safety cushion: Press a lock level and disunite the safety cushion socket.
- Turn off a nut (4), turn out an anchor bolt (5) and remove a side pillow (1). (2) - a dish-shaped washer, (3) – a washer.
|
|
Installation
|
|
- Installation is carried out in the sequence, the return to removal. At the same time adjust an anchor bolt and tighten a nut the moment of 55 Nanometers. Tighten the screw (6) the moment of 10 Nanometers.
|
|
During connection of the rechargeable battery in salon there should not be people. |
- Models with a side safety cushion: Shoot the insulating film from the negative plug of the rechargeable battery, attach at first positive (+), and then a negative cable (-) to the rechargeable battery.
- If after inclusion of ignition the safety cushion signaling device on the control panel does not die away, it is necessary to consider information from memory of malfunctions on HUNDRED.
|
|
|
|
