Audi S4

since 2000 release

Repair and operation of the car



Audi S4
+ Introduction
- Governing bodies and methods of safe operation
   Governing bodies and devices
   Information system of the driver (FIS)
   Unlocking and locking of the car
   Lighting and providing review
   Seats and niches
   Heater, ventilation and conditioner of air
   Automatic Transmission (AT)
   Communication and navigation
   Universal remote radio control of HOME LINK®
   Security systems
   Features of operation and auxiliary systems
   Running in
   Towage of the trailer
   In case of emergency
   Gas station of the car
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


4affa92a



Universal remote radio control of HOME LINK

Description

Universal remote radio control of HOME LINK ® can be programmed portable transmitters of already programmed devices.

Universal remote radio control of HOME LINK ® gives the convenient chance, without going out of the car, to use various devices, for example, garage gate / gate of the site, a security system, lighting of the house, etc.

Universal remote radio control of HOME LINK ® allows to replace three various portable transmitters of the corresponding devices with one (universal remote radio control). Mechanisms of garage and external gate most often belong to such devices. Programming of portable transmitters on your remote radio control is carried out near a front bumper on the right. There is a control unit.

For a possibility of control of various devices by means of universal remote radio control of HOME LINK ® it is necessary to program the corresponding transmitter previously. If after the first programming of the device do not function, then these devices should be checked for existence of a dynamic code.

The list of compatible portable transmitters can be received by fax: +49 (0) 6838 907 283 3333. More detailed information HOME LINK ® is relative and/or compatible to HOME LINK ® products it is possible to receive, having called on the duty-free hot HOME LINK line ® (0) 08000466 35465 or +49 (0) 6838 907 277 or visit the HOME LINK page ® in system the Internet

Programming of the transmitter

Programming of universal remote radio control of HOME LINK ® is carried out by the keys located in a sun-protection peak of the driver, and also from a front bumper.

From a sun-protection peak

Sun-protection peak of the driver

 PERFORMANCE ORDER

  1. Turn on the ignition/engine does not work.
  2. Press both extreme keys of universal remote control of HOME LINK ®, the light-emitting diode (A) will not begin to blink yet (approximately in 20 seconds).
  3. Press the HOME LINK key ® which you want to program.
  4. Wait until the light-emitting diode begins to blink (And). The five-minute stage of programming of the HOME LINK module ® begins.
  5. Go out of the car and become before it with the original portable transmitter of the drive of garage gate or other device on which you want to program the HOME LINK key ®.

From a front bumper

Right side of a front bumper

 PERFORMANCE ORDER

  1. You keep the original portable transmitter at a distance of about 0 - 30 cm under the right forward headlight at a bumper of your car.
  2. Press a key of turning on of the original portable transmitter.
  3. At the included function of the portable transmitter watch indexes of turn of the car. The positive result of programming of HOME LINK ® is confirmed by a triple blinking of system of the alarm light system.
  4. In the absence of a triple blinking of lamps repeat process of programming on other removal from a bumper.

The distance between the portable transmitter and the HOME LINK module located in a bumper ® is defined by the device which you want to program. Perhaps, programming will require several attempts.

Excess of a five-minute stage of programming is confirmed by a single blinking of system of the alarm light system. In this case it is necessary to repeat a programming stage from a sun-protection peak.

When programming two other keys be guided by the above-stated description. 3 from a sun-protection peak it is also necessary to begin with action if programming is carried out right after programming of the first key.

If after positive programming, nevertheless, the HOME LINK keys ® did not possible to open garage gate or other systems, then there is a probability of functioning of concrete system with a dynamic code. In this case programming of a dynamic code is necessary.

Programming of a dynamic code

Some devices demand additional programming of a dynamic code of universal remote radio control of HOME LINK ®.

Identification of a dynamic code

 PERFORMANCE ORDER

  1. Again press and hold pressed the HOME LINK key ® which you already programmed earlier.
  2. Watch HOME LINK light-emitting diode ® (A). If the diode quickly blinks in the beginning, and in 2 seconds burns continuously, then it means existence of a dynamic code of the corresponding device, for example, devices for opening of garage gate.
  3. The dynamic code is programmed in the following sequence:

Inclusion of function of the mechanism of the electric motor of the device for opening of garage gate

 PERFORMANCE ORDER

  1. To find a key of setup of the mechanism of the electric motor of the device for opening of garage gate. The exact location and color of a key depends on brand of the manufacturer of the device.
  2. Press a key of setup of the mechanism of the electric motor of the device for opening of garage gate. (At the same time the light-emitting diode of "setup" of the mechanism of the electric motor, as a rule, burns). Now at your disposal about 30 seconds for implementation of programming of the HOME LINK key located in a sun-protection peak ®.

Programming from a sun-protection peak

 PERFORMANCE ORDER

  1. Again press and release the HOME LINK key ® which you already programmed earlier.
  2. For completion of programming of a dynamic code press the HOME LINK key ® again.

After programming by a key of a sun-protection peak the device for opening of garage gate has to distinguish HOME LINK signal ® and open gate after pressing of the HOME LINK key. If necessary now it is possible to program other keys.

In the presence of the assistant process of programming of a dynamic code can be simplified and accelerated. For opening of garage gate it is necessary for completion of process of setup of some devices the third time press the HOME LINK key ®.

In case of difficulties of programming of a dynamic code studying of the operation manual on the device for opening of garage gate / other device perhaps will help.

HOME LINK use

Use of the programmed devices is carried out by the HOME LINK keys located in a sun-protection peak of the driver ®.

 PERFORMANCE ORDER

  1. Turn on the ignition/engine does not work.
  2. Press the programmed HOME LINK key ®. There is a control of the device programmed on this key (for example, the device for opening of garage gate).

During a manipulation HOME LINK® light-emitting diode burns with command keys.

Dumping of the programmed these HOME LINK keys ®

Both extreme command keys dumping of all programmed data of HOME LINK ® is possible.

 PERFORMANCE ORDER

  1. Turn on the ignition/engine does not work.
  2. Press both extreme keys, the light-emitting diode will not begin to blink yet.
  3. Release keys.

After dumping of data of programming of keys of universal remote radio control of HOME LINK ® the device is in the mode of control again and is ready to new programming.

Separate dumping of the programmed keys is impossible.

For the reasons of safety dump programming of the HOME LINK keys before sale of the car.

Reprogramming of one HOME LINK key ®

There is a possibility of reprogramming of one HOME LINK key ® without change of the programmed provisions of other keys.

From a sun-protection peak

 PERFORMANCE ORDER

  1. Press the urgent HOME LINK key ®, slowly the light-emitting diode will not begin to blink yet.

From a front bumper

 PERFORMANCE ORDER

  1. You keep the original portable transmitter of the drive of garage gate or other device at a distance of about 0-30 cm under the right forward headlight at a bumper of your car. The necessary distance is defined by the device which you want to program.
  2. Press a key of turning on of the original portable transmitter of the device for opening of garage gate or other device.
  3. At the included function of the portable transmitter watch indexes of turn of the car. The positive result of programming of HOME LINK ® is confirmed by a triple blinking of system of the alarm light system.
  4. In the absence of a triple blinking of lamps repeat process of programming on other removal from a bumper.

After a triple blinking of the alarm light system there is a dumping of earlier programmed data of HOME LINK:® and the new device is programmed. For use of the new device press the programmed HOME LINK key ®.

Programming, perhaps will require several attempts. Duration of process of adjusting provision of each attempt has to make at least 15 seconds. Only after that it is possible to pass to other position. Watch at the same time lamps of indexes of turn.