Audi S4

since 2000 release

Repair and operation of the car



Audi S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Specifications
   Diagnostics of malfunctions of onboard electric equipment - the general information
   Rassoyedineniye of sockets
   Check of the electric motor of a screen wiper
   Check of the warmed back glass
   Check of stoplights
   Removal and installation of a sound signal
   Removal and installation of sensors of the parking
   Replacement of the battery of the remote control of the ignition key
   Relay and safety locks
   Replacement of glow lamps of devices of external lighting
   Removal and installation of headlights
   Removal and installation of the side repeater of turns
   Removal and installation of an additional stoplight
   Removal and installation of a back lamp
   Removal and installation of a lamp of illumination of registration plate
   Removal and installation of plafonds of internal lighting
   Removal and installation of the control panel
   Removal and installation of the understeering switch
   Removal and installation of switches of a forward door
   Removal and installation of the switch of light
   Removal and installation of the switch of a window regulator in a back door
   Removal and installation of the switch of a trunk lid
   Removal and installation of the switch of the parking brake
   Removal and installation of the switch of illumination of a ware box
   Removal and installation of switches of the central console
   Removal and installation of the radio receiver / navigation device / CD changer
   Removal and installation of loudspeakers
   Removal and installation of antennas
   Removal and installation of the tank of liquid of the windscreen washer/electric motor of the pump
   Removal and installation of the electric motor of screenwash
   Removal and installation of the electric motor on back glass (Station wagon)
   The uniform lock - the general information
   Removal and installation of a locking element of a cover of the fuel tank
   Digital tire of data of CAN
   + Schematic diagrams of electric equipment


4affa92a



Removal and installation of a back lamp

Sedan

Removal

 PERFORMANCE ORDER

  1. Open an opening (1) in facing of a luggage carrier.
  1. Turn out the screw (3) and cast away a back lamp outside, having taken out at the same time from a wing a spherical finger.
  1. Disunite the socket on the lamp panel.

Installation

 PERFORMANCE ORDER

  1. Join the socket on the lamp panel.
  1. Establish a back lamp on a body so that fingers were pressed into plugs (7). At the same time you monitor the correct provision of consolidation.

    1 — the Dimensional lamp
    2 — the Stoplight / a dimensional lamp
    3 — the Index of turn back
    4 — a backing Lamp
    5 — the Foggy lamp
    6 — the Connecting plug
    7 — Plugs

  1. Tighten the screw (3) the moment of 6 Nanometers.
  1. If it is necessary, turn off a nut (2) and you will expose a back lamp so that to provide a uniform gap in relation to adjacent parts of a body. Tighten a nut the moment of 12 Nanometers.

Replacement of glow lamps

 PERFORMANCE ORDER

  1. Squeeze 2 lock levels (shooters) and remove the lamp panel from a back lamp.

    1 — the Dimensional lamp
    2 — the Stoplight / a dimensional lamp
    3 — the Index of turn back
    4 — a backing Lamp
    5 — the Foggy lamp
    6 — the Connecting plug
    7 — Plugs

  1. Press lamps with (1) on (5) into cartridges, turn and take out. Replace lamps with new.

If the backing lamp lamp after replacement after all does not burn, it is necessary to check the switch. The switch is at the check point over a flange of a power shaft.

Versatile person

Removal

 PERFORMANCE ORDER

  1. Open a door of a back and take out a cap from facing.
  1. Turn out a bolt (1). Cast away a back lamp outside, having taken out at the same time a spherical finger from a wing.
  1. Disunite the socket of the lamp panel.

Installation

 PERFORMANCE ORDER

  1. Join the socket of the lamp panel.
  1. Establish a back lamp on a body so that fingers were pressed into epiploons (6). At the same time you monitor the correct provision of consolidation.

    1 — the Foggy lamp
    2 — the Index of turn back
    3 — a backing Lamp
    4 — the Stoplight / a marker light
    5 — the Connecting plug
    6 — Plugs for fingers

  1. Tighten the screw (1) the moment of 6 Nanometers.
  1. If it is necessary, turn off a nut (2) and you will expose a back lamp so that to receive a uniform gap in relation to adjacent elements of a body. Tighten a nut the moment of 12 Nanometers.

Replacement of glow lamps

 PERFORMANCE ORDER

  1. Press four lock levels outside of (shooters on an accompanying illustration) and remove the lamp panel from a back lamp.
  1. Press glow lamps with (1) on (4) into cartridges, turn and take out. Replace lamps with new.

    1 — the Foggy lamp
    2 — the Index of turn back
    3 — a backing Lamp
    4 — the Stoplight / a marker light
    5 — the Connecting plug
    6 — Plugs for fingers

If the backing lamp lamp after replacement after all does not burn, it is necessary to check the switch. The switch is at the check point over a flange of a power shaft.